top
Yongkang Puli Caster Manufactory
News List
Contact Us
Yongkang Puli Caster Manufactory
Yongkang Puli Caster Manufactory
Add: Shuchuan Industrial Area,Yongkang,
Zhejiang,China.
Foreign Department:
Phone:13705898931
Tel: 0086-579-87530898
Fax: 0086-579-87530897
E-mail: 02@puli-caster.com
Ministry of Internal Trade:
Phone:13857953186
Tel: 0579-87530896
Fax: 0579-87530897
E-mail: 02@puli-caster.com
Wheels choice (Hits:) 
Origin Author Add Time2012-12-10
fontSize: T|T

The choice of wheels: single round of industrial casters with a wide range of size, type, tread not want to.

    Select the appropriate wheels to take in the following conditions:
   A weight-bearing
   B venue environment
   C various special climate, such as humidity, high temperature, or cold.
   D working environment containing chemicals, blood, grease, oil, salt and other substances.
   E impact, collision and quiet driving requirements. The single wheel is the most important factor to determine the carrying capacity and traveling light and flexible.

   Wheel material is characterized by:

   Compression strength: compression test procedure, the sample is exposed to the maximum compressive stress, units banknote MPa.

   Hardness: means for measuring the hardness of the rubber and the other tire and wheel core material, with a Shore "A" or "D".

  Elongation: the role of the tension, the distance between the specimen fracture when marking to increase the ratio of the amount of the initial gage, expressed in percentage.

  Impact strength: the material to withstand a free fall heavy loads imposed by the violent impact of the performance. / Lb ft / lbs the stamping reactive test temperature expressed.

  Resistance to deformation under the weight of a location change into flat, that test samples to withstand a static pressure load: long heavy wheels, after the stipulated shed load after the end of the compression time, sub-point change table height percent compared with the original height.

  Operating temperature: measured at rated load operating temperature range.

  Adhesion: a speed of 6 inches / minute tires is peeled off from the top of the bonded wheel core required force, in pounds divided by the line width of the tire calculated.

  Tensile strength: wheels from the fracture of the transverse cross-sectional force required. Lateral force in pounds divided by the sample area (square inch) then.

  Water Absorption: The increase in weight of the test sample. Weight after a certain procedure test with a percentage of the initial weight of said samples.

  Member of the anti-wrapped cover: to avoid and other material wound around the axle and the bracket and wheels gap, so that the wheel can rotate freely.

  Seals: Avoid steering bearings or the single wheel bearings into the dust, to maintain its lubricity, easy rotation.

  Lock: spring latch lock steering bearings (four or two locking) activities casters lock for fixed casters.

 Single wheel brake: the wheel the sleeve or tire surface, hand or foot brake valves manipulation device.

 Full brake latch: to the conveyance Hereinafter, the apparatus so that it is fixed at a certain position.

 : Including steering arm lever, rubber bumpers, mats, locking pads and other parts with a specific purpose. If you want to know the specific, direct contact with manufacturers.

 

keyworks:Wheels series ,Medium wheel,Light wheel,Special castor ,Yongkang Puli Caster Manufactory

bottom
底部
Home | Lightweight Wheels | Industrial Wheels | All Products | About Puli | Certificate | News | FAQS | Feedback | SiteMap | Login
Keywords:Lightweight wheelIndustrial wheel、Medium-sized round、Heavy-duty wheelFurniture roundSpecial castersWheel
Yongkang Puli Caster Manufactory. Copyright:2012-2012 Address: Shuchuan Industrial Area,Yongkang,Zhejiang,China.
Technical support: Easthardware
Message